Hexagon Measurement      Systems

No matter what Hexagon measurement equipment or software you use, we want to hear your ideas and suggestions on how we can improve.

  • Your feedback and voting will benefit the majority of users.
  • You have 10 votes which you can allocate to your own or other users ideas.
  • We will focus on trying to realize the top voted items in our future products.

Thanks for your assistance in helping us shape the future.

+11
Завершен

Set the limit angle value to measure 180° bends

Nicolas Pétré 6 лет назад в Metrology Software / TubeShaper обновлен anthony vianna 3 года назад 3

Today, 180° bends require additionnal point when the angle is higher than 178° (?).

This limit value should be editable (tupe inspectionsettings) to be able to operate the same way on slightly smaller angles (175° for inst.).

+7
Отклонен

IP deviation as 3D distance

Alexander Schneeberger 6 лет назад в Metrology Software / TubeShaper обновлен anthony vianna 3 года назад 4

3D distance from nominal to measured IP (in addition to the X,Y,Z values)

+6

Preview window for CAD import

Liviu 5 лет назад в Metrology Software / TubeShaper обновлен neil kay 4 года назад 1


As a TubeShaper user, when I import a CAD model that contains assembled tubes with or without brackets (IGES/STEP), I want to be able to select wich one has to be extracted and afterwards measured/reported.


It will be nice to have a Preview window of the CAD model and select which one has to be extracted, and also to select which straight, of the selected tube, has to be considered my 1st one.

Regards,

Liviu

+6
Завершен

Create Straight Tube Project

trung van 6 лет назад в Metrology Software / TubeShaper обновлен anthony vianna 3 года назад 4

Crazy as it sounds, but we do have straight tubes that we measure too, some with flanges or fittings at the ends.  I know that there is the toolbox to measure a straight, but it is limited to just a straight.  Would like to be able to create and inspect a straight tube with or without flange profiles and check for the deviations.

+6
Завершен

Modification of the Protocol Header / Customer Request

Holger 6 лет назад в Metrology Software / TubeShaper обновлен anthony vianna 3 года назад 5

We need more Variables ind the Header of the Protokoll.

The Customers need to insert.

1. Customer

2. Part

3. Controller

4. Tube Material

5. Bender

6. Comments

7. ...etc.

+5
Завершен

Need Square Tubing!!!!

Scott Martin 6 лет назад в Metrology Software / TubeShaper обновлен anthony vianna 3 года назад 4

Been begging for square tubes since TubeShaper came out.  I have many customers asking for this.

+5
На рассмотрении

Add bent tube to straight tube capabilities

Joe 6 лет назад в Metrology Software / TubeShaper обновлен neil kay 4 года назад 2

I measure a lot of bent tubes with copes (fish mouth cuts) on the ends of the tubes.  Would like to have the capability in TubeShaper to take  a measured bent tube (with measured cylinders on each end) and convert it to a straight state with the measured end cylinders in the correct orientation.  Then the straight tube can be exported as a CAD model so it can be used in a tube laser machine.

+5
На рассмотрении

Additional method for measuring long tubes (leap-frogging)

George Koskinas 7 лет назад в Metrology Software / TubeShaper обновлен neil kay 4 года назад 1

Currently the only method available for measuring long tubes (leap-frogging) is the "Move Tube" where it is required to measure two straights. If all straights are just too big to allow for selection/measurement of any two, this obviously won't work. Perhaps we can add an additional method, similar to that of G-Tube, where we add a displacement T-square, perpendicular to any straight.

+4
Отклонен

Apply new default settings to existing projects

Nicolas Pétré 5 лет назад в Metrology Software / TubeShaper обновлен anthony vianna 3 года назад 2

When a user changes his default report Template (ex: change the Logo), those new settings will be applied only on new projects.

If he has 1000 existing projects, there is no way to retro apply the new settings on the old project but changing one by one.

+4
Завершен

Integrate leapfrog using touchprobe

sebastiaan kuiper 6 лет назад в Metrology Software / TubeShaper обновлен anthony vianna 3 года назад 2

Please integrate leapfrog using touchprobe. When doing the current leapfrog (measure last two straights) it is sometimes not possible to measure tubes with a very long straight (2000-3000mm) in between the bends with a "standard" tubearm. This will be possible using a traditional leapfrog (or two).



Сервис поддержки клиентов работает на платформе UserEcho